An automatic compensation method on compression effect and surface elasticity measurement based on t

来源 :Science China(Technological Sciences) | 被引量 : 0次 | 上传用户:kangliwonuer
下载到本地 , 更方便阅读
声明 : 本文档内容版权归属内容提供方 , 如果您对本文有版权争议 , 可与客服联系进行内容授权或下架
论文部分内容阅读
Atomic force microscope(AFM),as an important instrument in micro/nano operation,has been widely used to measure sample’s height information.However,the so called compression effect,due to force aroused from the contact of AFM tip with a sample surface,would result in imprecision of the surface’s height measurement,i.e.,the measured height is lower than expected.Up to now,there is not any effective and rapid method to attenuate this kind of measurement error.Thus,in this paper,an algorithm to obtain high accurate height measurement is proposed.Firstly,the concept of force curve is used to analyze the basic principle of the compression effect.Secondly,an automatic compensation method by fusing the height signal and the deflection signal is proposed.The proposed algorithm can also be used to obtain a surface elasticity image.Finally,in order to validate the proposed method,two experiments are conducted with respect to mutli-wall nano-carbon tubes on a silicon substrate and graphemes on a mica substrate. Atomic force microscope (AFM), as an important instrument in micro / nano operation, has been widely used to measure sample’s height information. However, the so called compression effect, due to force aroused from the contact of AFM tip with a sample surface, would result in imprecision of the surface’s height measurement, ie, the measured height is lower than expected. Up to now, there is not any effective and rapid method to attenuate this kind of measurement error. Thus, in this paper, an algorithm to obtain high accurate height measurement is proposed. Firstly, the concept of force curve is used to analyze the basic principle of the compression effect. Secondarily, an automatic compensation method by fusing the height signal and the deflection signal is proposed. The proposed algorithm can also be used to obtain a surface elasticity image. Finally, in order to validate the proposed method, two experiments are conducted with respect to mutli-wall nano-carbon tubes on a silicon substrate and graphemes o n a mica substrate
其他文献
目前,石砌体墙面勾缝种类很多,有凸缝、凹缝、平缝和假缝。多数施工单位采用凸缝,有的为了美观勾假缝,一般做法是在墙体砌完后统一勾缝,但这样做缝内很难清理干净,勾缝砂浆
先天性唇腭裂会造成患者语音功能异常,唇腭裂患者语音异常检测及分析方法的研究有助于对语音功能的矫正。该文就近期对唇腭裂患者语音检测及分析的方法作一综述。 Patients
“为了每一个学生的发展”是教育的根本宗旨,也是新课程所追求的价值取向。湖北省随州市曾都区洛阳镇小学以学生发展为本开发校本课程。一是教师经常把课堂设在室外、校外,让
2004年秋季,我省104所高中学校的所有高一年级学生46475人如期进入新课程实验,当年参加新课程学科培训的专任教师达2878人;2005年,高中学校数增加到107所,参加实验的年级达到
人们往往关注小区入口对交通、防御、形象及标示的作用,而忽略它对小区物理环境的影响。从建筑物理环境的角度关注小区入口的形式及位置设计是提升建筑设计质量的重要一环。
语文本应是最有灵性、最具活力、最具趣味的学科,但事实恰恰相反,学生把学习语文看作是最痛苦的事。当前,语文教育的最大悲剧莫过于“应试训练”。教师按大纲要求,将教材分解
蒸是用水蒸气加热的方式烹饪菜肴。蒸菜原汁原味,最能保留营养成分。它不仅适用于荤素各种食材,同时具有丰富的口感和千变万化的搭配。  蒸菜一举多得  相比煎、炸、炒高达300℃的高温,用水蒸的温度不超过100℃,热分解损失和氧化损失都较少,更不会产生对人体有害的物质。另外,蒸菜清淡少油,能有效控制油脂摄入。而且,蒸菜过程中没有油烟烦恼,也保护了烹饪者的健康。有人认为水煮或焯烫很健康,但其实在烹饪过程中
例1如图1所示,有一倾角为θ的光滑斜面,一辆小车沿斜面滑下,车上有一单摆做微小摆动,摆长为l,求单摆的振动周期.解析设单摆随小车一起沿 Example 1 As shown in Fig. 1, the
新一轮数学课程改革已进入推广阶段,教师的教学理念及学生的学习方式也发生了实质性的变化。对现在还在使用老教材的教师来说,利用老教材教出新理念已迫在眉睫。在这一思想的
水上的道路水上的道路是指用各种材料在河、湖、江、海上架起的桥,它能帮助人们或车辆方便、快速地从河、湖、江、海的一边到达另一边。 Watery roads Watery roads are bri