放电等离子烧结压力对超细WC-Co硬质合金性能的影响

来源 :硬质合金 | 被引量 : 0次 | 上传用户:iloveyanqing
下载到本地 , 更方便阅读
声明 : 本文档内容版权归属内容提供方 , 如果您对本文有版权争议 , 可与客服联系进行内容授权或下架
论文部分内容阅读
通过分析放电等离子烧结致密化过程,确定了致密化温度;研究了SPS烧结过程中压力对WC-Co硬质合金致密化、显微组织及性能的影响。结果表明,放电等离子烧结粉末在1 130℃时,达到最大收缩率;烧结压力的增加,样品的致密度、硬度增加;断裂韧性的变化集中在11.5~12.1 MPa.m1/2之间,和硬度的变化呈现相反的趋势;烧结压力相对较小时,样品WC晶粒较粗大且不均匀;在40 MPa和55 MPa时,晶粒相对较小且分布均匀。要得到高性能、高致密度的样品,合理的烧结温度在1 200℃以上,烧结压力为40 MPa。 The densification temperature was determined by analyzing the densification process of spark plasma sintering. The effects of pressure on the densification, microstructure and properties of WC-Co cemented carbide during SPS sintering were investigated. The results show that the maximum shrinkage rate of the spark plasma sintering powder reaches to 1 130 ℃, the sintering density increases and the hardness increases. The fracture toughness changes mainly between 11.5 ~ 12.1 MPa.m1 / 2, and the hardness Showed the opposite trend. When the sintering pressure was relatively small, the grains of WC were coarse and inhomogeneous. At 40 MPa and 55 MPa, the grains were relatively small and uniformly distributed. To get high performance, high density samples, a reasonable sintering temperature above 1200 ℃, sintering pressure 40 MPa.
其他文献
目的 探讨PBRM1和P53蛋白在肾癌中的表达和临床意义.方法 应用免疫组化方法对66例肾癌组织进行PBRM1和P53蛋白检测.结果 在肾癌组织中PBRM1和P53蛋白表达阳性率分别为62.1%和3
目的 探讨深板层角膜移植治疗格子样角膜营养不良的临床效果.方法 对24例(32眼)视力明显受损的格子样角膜营养不良患者行深板层角膜移植术,术后随访6~ 36个月,观察视力和并
针对某车生产阶段出现的空调不制冷问题,使用GDS监测空调制冷剂压力与压缩机离合器吸合关系,锁定空调制冷剂压力传感器故障,后续通过设备检测找到了零件失效的根本原因,并采取有
细胞色素P450酶(CYPs)是1个广泛存在于人体组织中,以铁卟啉为辅基的蛋白质家族,大多为单加氧酶,可以催化多种代谢反应[1].文献已报道细胞色素P4501B1(CYP1B1)是1种在许多与激
经过大量的现场实验与理论研究,充分考虑到二次冷轧机组的设备与工艺特点,在首次提出“切水”与“冷却”综合控制目标函数的基础上,建立了一套冷却液喷淋综合控制数学模型,并
A simulating experiment was carried out on the interaction between natural precipitation and soil. The results demonstrated that the contents of heavy metals (V
进行了1.8%阿维菌素·吡虫啉WP不同剂量防治水稻飞虱的药剂试验。结果表明:该药剂对水稻飞虱有较好的防治效果。提出了施药适宜时间为稻飞虱低龄若虫突增期,推荐用量为300~45
一、江西省印刷产业的现状截止到2006年底,江西省共有各类印刷企业(不含复印、打印企业)1661家,其中出版物印刷企业159家(其中从事专项排版、制版、 First, the current sta
山地丘陵为主的地形,再加上侵蚀力强的水力和抗蚀力弱的母质和土壤,使福建省生态环境相当脆弱,水土流失潜在危险大.另一方面,丰富的水热资源则为生态修复提供了良好的基础.作
基于ANSYS/LS-DYNA分析平台构建单道次渐进成形锥形件的有限元模型,利用数值模拟和实验方法研究单道次渐进成形锥形件的壁厚均匀临界成形角。通过研究不同成形角的锥形件,获