【摘 要】
：
李方训教授生于一九○二年,江苏仪征人,一九二五年在金陵大学毕业后,即从事文化教育工作,先后在金陵大学、南京大学任教三十余年,曾兼任金陵大学理学院院长,解放后曾任金陵
论文部分内容阅读
李方训教授生于一九○二年,江苏仪征人,一九二五年在金陵大学毕业后,即从事文化教育工作,先后在金陵大学、南京大学任教三十余年,曾兼任金陵大学理学院院长,解放后曾任金陵大学校务委员会主任委员。一九五二年起担任南京大学副校长,一九五五年受任为中国科学院学部委员。先生毕生致力于教学和科学研究工作,治学谨严,诲人不倦,为祖国文化教育事业的繁荣和科学研究的发展,做出不少贡献。
Professor Li Fangxun was born in 1922 in Yizheng, Jiangsu Province. After graduating from Jinling University in 1925, he engaged in cultural and educational work. After teaching for more than thirty years at Jinling University and Nanjing University, he served as the Faculty of Science of Jinling University Dean, after liberation served as chairman of Jinling University School Board. He served as vice president of Nanjing University in 1952, and served as a member of the Chinese Academy of Sciences in 1955. Life devoted to teaching and scientific research, rigorous scholarship, tireless education, for the prosperity of the motherland’s cultural and educational undertakings and scientific research, make a lot of contributions.
其他文献
Overlapped time division multiplexing (OvTDM) is a new type of transmission scheme with high spectrum efficiency and low threshold signal-to-noise ratio (SNR).
湖南省常德市纺织机械配件厂是生产棉纺织机械配件的专业厂,各种铸件达六百多种,需不同形状、规格的型芯四百种以上。该厂3/4以上铸件为湿型机器造型,由于产品的型号多,模板
我们在Y38滚齿机上附加了一套工装,用来加工长轴头部花键。经几年使用,质量可靠,效果良好。使用时装上就能代替花键铣床,不用时卸下,完全恢复原机性能。该工装由上、下两个
一切事物都有其自身的规律,任何行动都有它内在的原因,因此,在这个意义上说,去年年底在经互会特别会议上通过的、因大家庭各国政府领导人签署的经互会成员国科学技术进步综
The effects of soil animals on soil nitrogen (N) mineralization and its availability were studied by investigating soil animal groups and their amounts of macro
近几年来,我们研究了一种新型白口抗磨铸铁——硼系合金白口抗磨铸铁。它在成分设计上首先考虑到我国的资源情况,在保证合金性能的前提下,尽可能选用我国资源丰富的价廉的元
对比试验与分析证明,新型陶瓷刀具比YG6X硬质合金刀具加工低镍铬冷硬铸铁轧辊的表面质量——包括表面粗糙度、表面显微裂纹、表面宏观应力和表面显微硬度有明显改善。同时用
日本第105次铸造会议于1984年5月18日至5月21日在日本神户国际会馆举行。中国铸造科技工作者共17人应邀参加了会议。会议分五个会场同时进行。共发表论文135篇,会议期间在神
The interest in the development and improvement of dynamic global vegetation models (DGVMs), which have the potential to simulate fluxes of carbon, water and ni
图1所示为电机线圈架零件,它是用图2所示模具,靠滑块的摆动一个ω角而卷成圆的。此模具结构比较简单,但每个具体零件的设计又比较复杂,尤其是几个重要尺寸更难以确定,如L、W