Promoter methylation of Wnt/β-Catenin signal inhibitor TMEM88 is associated with unfavorable prognos

来源 :癌症生物学与医学(英文版) | 被引量 : 0次 | 上传用户:jinwei001
下载到本地 , 更方便阅读
声明 : 本文档内容版权归属内容提供方 , 如果您对本文有版权争议 , 可与客服联系进行内容授权或下架
论文部分内容阅读
Objective: Recent research has indicated that altered promoter methylation of oncogenes and tumor suppressor genes is an important mechanism in lung cancer development and progression. In this study, we investigated the association between promoter methylation of TMEM88, a possible inhibitor of the Wnt/β-Catenin signaling, and the survival of patients with non-small cell lung cancer (NSCLC). Methods: Twelve pairs of tumor and adjacent non-tumor samples were used for microarray analyses of DNA methylation and gene expression. For validation, more than two hundred additional samples were analyzed for methylation using bisulfite pyrosequencing and for gene expression using qRT-PCR. Then the cell function were tested by wound healing, transwell, CCK8 and cell cycle assay. Results: Our analysis of patient specimens showed that TMEM88 methylation was higher in NSCLC tumors (82.2% ± 10.3, P <0.01) compared with the adjacent normal tissues (65.9% ± 7.2). The survival analysis revealed that patients with high TMEM88 methylation had a shorter overall survival (46 months) compared with patients with low TMEM88 methylation (>56 months;P=0.021). In addition, we found that demethylation treatment could inhibit tumor cell proliferation, migration, and invasion, which was supportive of an association between methylation and survival. Conclusions: Based on these consistent observations, we concluded that TMEM88 may play an important role in NSCLC progression and that promoter methylation of TMEM88 may serve as a biomarker for NSCLC prognosis and treatment.
其他文献
本文通过对球形和锥形零件在接深过程中各部分的应力分析 ,得到了拉深过程中悬空区切向压应力最大值的计算公式 ,以此作为引发内皱的条件 ,在保证工件不被拉裂的前提下 ,建立
期刊
通过对曲面零件带筋拉深中筋的成形过程的分析 ,推导了拉深筋的成形力公式 ,并且进行了试验验证 .同时 ,又得到了保证拉深零件时压边圈不被抬起的最小压边力公式 The formin
本文通过在镍基自熔合金粉末中添加少量稀土 ,探讨稀土对 Ni-WC喷焊层组织和耐磨性的影响 .结果表明 ,适量地加入稀土可以改善喷焊层焊态组织 ,提高喷焊层硬度和耐磨性 ,而且
期刊
期刊
大型薄板球面体成形一直是板料成形工艺中的难点 ,本文对大型超薄壁球壳的制造提出一种整体成形新方法 .通过应用无模爆炸成形技术 ,解决了薄壁和超薄壁球壳的制造 ,并通过大
期刊
本文利用流体力学及传热理论 ,开发了耦合传热的三维充型模拟软件 ,应用该软件及 TEMP(三维快速凝固模拟软件 )对选定铸件进行了充型及凝固模拟 ,其结果可为生产实际的工艺设