【摘 要】
:
The mid-infrared (mid-IR) second-order optical nonlinearity of the barium titanate (BTO) thin films was characterized by second harmonic generation (SHG). The epitaxial BTO thin films were grown on strontium titanate substrates by pulsed-laser deposition.
【机 构】
:
DepartmentofElectricalandComputerEngineering,TexasA
【出 处】
:
PhotonicsResearch
论文部分内容阅读
The mid-infrared (mid-IR) second-order optical nonlinearity of the barium titanate (BTO) thin films was characterized by second harmonic generation (SHG). The epitaxial BTO thin films were grown on strontium titanate substrates by pulsed-laser deposition. From the azimuthal-dependent polarized SHG measurements, the tensorial optical nonlinear coefficients, , and ferroelectric domain fraction ratio, , were resolved. Strong SHG signals were obtained at the pumping laser wavelength between 3.0 and 3.6 μm. The SHG intensity was linearly dependent upon the square of the pumping laser power. The broadband mid-IR optical nonlinearity enables BTO thin films for applications in chip-scale quantum optics and nonlinear integrated photonic circuits.
其他文献
应用一维粒子模拟方法数值研究了超短超强激光和稠密等离子体的相互作用。结果表明,在等离子体中激发起无规则的电场波动,同时在等离子体中产生温度很高的电子。
采用激光填丝焊方法焊接了6082铝合金,研究了焊接速度对焊接接头热影响区软化的影响。结果表明,当温度为430~560 ℃时,接头热影响区会发生明显的β″强化相溶解, β″相的数量明显减少,接头的硬度和拉伸强度减小,发生了热影响区的深度软化效应,热影响区的软化区成为接头最薄弱的区域。当激光功率为4250 W,焊接速度为2.7 m·min-1时,接头热影响区的局部深度软化现象得到有效抑制,其平均硬度值大于82 HV,抗拉强度增大至249 MPa,接头的拉伸断裂发生于焊缝。
本文介绍光纤直径动态测量中采用的激光扫描技术以及纤径控制中采用的逐点比较式新技术.对于直径为50~250微米的光纤,测量误差在±0.5%以内.结果以数字形式显示,并转换成模拟信号,有效地控制光纤拉丝机的拉丝速度,从而保证了光纤直径均匀.
A time-division multiplexing method for computer-generated holograms (CGHs) is proposed to solve the problem of the limited space-bandwidth product. A three-dimensional (3-D) scene is divided into multiple layers at different depths. The CGH corresponding
采用飞秒钛宝石激光放大器二次谐波为泵浦源,行波泵浦BBO晶体光参量放大器,获得了可调谐输出(0.44~2.6 μm),最大输出能量约40 μJ/脉冲,测量了参量激光的调谐特性、能量分布和线宽,理论与实验符合较好。
A novel compensation method for temperature-dependent gain tilt of L-band erbium-doped fiber amplifier (L-EDFA) is proposed, in which the attenuation between stages is the only parameter to be adjusted. A simple linear relationship between the attenuation