• 不 限
  • 期刊论文
  • 硕博论文
  • 会议论文
  • 报 纸
  • 英文论文
  2. 您的位置
  3. 首页
  4. 会议论文
  5. Tribological behaviors of diamond-like carbon film in different atmospheres

Tribological behaviors of diamond-like carbon film in different atmospheres

来源 :Fifth International Conference on Surface Engineering(第五届表面工 | 被引量 : 0次 | 上传用户：netchina123
【摘 要】
：
Friction behaviors of the diamond-like carbon (DLC) film sliding against Si3N4 ball were investigated on a ball-on-disk tester in different atmospheres.The worn surface morphologies of the DLC films w
【作 者】
：
Xia Wang Peng Wang Shengrong Yang Junyan Zhang 
【机 构】
：
State Key Laboratory of Solid Lubrication,Lanzhou Institute of Chemical Physics,Chinese Academy of S
【出 处】
：
Fifth International Conference on Surface Engineering(第五届表面工
【发表日期】
：
2007年12期
【关键词】
：
DLC film tribological behaviors atmospheres 
下载到本地 , 更方便阅读
下载此文 赞助VIP
声明 : 本文档内容版权归属内容提供方 , 如果您对本文有版权争议 , 可与客服联系进行内容授权或下架
论文部分内容阅读
　　Friction behaviors of the diamond-like carbon (DLC) film sliding against Si3N4 ball were investigated on a ball-on-disk tester in different atmospheres.The worn surface morphologies of the DLC films were observed on a scanning electron microscope (SEM) and a 3-D surface profilometer,respectively.The chemical states of some typical elements on the worn surface of DLC film were revealed by means of X-ray photoelectron spectroscopy (XPS).Interesting experimental results which are quite different from previous reports were obtained.
其他文献
Preparation of Ag nanoparticles colloid by pulsed laser ablation in distilled water
The Ag nanoparticles colloid was prepared by pulsed laser ablation for different time in 10 ml distilled water without any surface active agent,and it was analysed by means of UV-visible spectrophotom
会议
Laser ablationAgNanoparticlesColloid
Status quo of research of coordination agents in cyanide-free Alkaline Zinc-Nickel alloy electroplat
In this article,the advantages of zinc-nickel alloy electroplating were introduced.It is indicated that the technological key of zinc-nickel electroplating is selection of coordination agents and brig
会议
The Study on the Dispersants and Structures of Ni-P-α-Al2O3Composite Electroless Plating Coating
The composite electroless plating layer that consists of the Ni-P continuous phase and the dispersed particle phase has higher hardness,wearability and special physical and chemical properties than th
会议
composite electroless platingNi-P alloyα-Al2O3dispersants
Study on Electrical Properties and 1064nm Pulse Laser Damage of Vanadium Oxide Thin Film
Vanadium dioxide is well known for the reversible thermally-induced semiconductor-metal phase transition which is accompanied by large changes in electrical and optical properties near 68 ℃.In order t
会议
thin film techniqueelectrical propertylaser damagevanadium oxide
The effects of surface modifications on tin-doped indium oxide films:optoelectrical,wettability and
Surface modifications were performed on the tin-doped indium oxide (ITO) substrates for optoelectronic devices,using the different treatment methods (ultrasonic degreasing,aquaregia treatment,base (Na
会议
Tin-doped indium oxideOptoelectrical propertiesWettabilityChemical compositio
The investigation of surface nanocrystallization of structural steel induced by Supersonic Fine Part
The nanostructured surface layers were fabricated on a thermal refining chrome-silicon alloy steel and a hypoeutectoid medium carbon steel by mean of Supersonic Fine Particles Bombarding (SFPB) based
会议
Supersonic Fine Particles Bombardingrobot systemsurface nanocrystallizationch
Study on the Polishing Characteristics of the Magnetic Abrasives Finishing to the Slender Pipe
Polishing the inner surface of slender pipe is very difficult,especially for the curve pipe.Because a usual tool do not into the inner of the surface of a curve pipe,and making to automation do not ac
会议
Magnetic abrasive finishingMagnetic fluxMagnetic abrasive particles and slende
Numerical Simulation of Residual Stress Field Induced by Ultrasonic Shot Peening
In this paper,a 3D finite element model is established to simulate the ultrasonic shot peening process by using a finite element software ABAQUS.The residual stress distribution of the AISI 304 stainl
会议
Ultrasonic Shot PeeningFinite Element AnalysisResidual Stress Field
Effect of High Pressure Waterjet Peening on Surface Strengthening Properties of 7075-T651 Aluminum A
The surface roughness and surface integrity resulting from net-shape processing may be detrimental to the fatigue-life and cerrosion resistance of engineering components.The most common methods enroll
会议
High pressure WJPResidual stressFatigue lifeSurface quality
Formation Mechanism of the Frictionaily-formed Protective Coating by Using Self-repairing Material U
Quite recently,with development of the nano-technology,nano-particles of metal,metal oxides and non-metal have been used in industrial application as additives in lubricating oils.In this condition,a
会议
Silicate particlesLubricating oilAdditiveFriction and wearFrictionally-forme